Lindsay Engraving Tools has unparalleled
experience. The owner, Steve Lindsay, has hand engraved full time for
25 years, and designed and made engraving tools for
He knows how he likes his tools to function and work for
his engravings, and the tools are being made available to fellow
metal artists, engravers and jewelers.
Don't settle for imitation or knockoff
- When quality means everything. In Your work and Ours!
Family Owned - Designed in USA and Made in USA!
Metal Handle (two types) for your Lindsay®
Graver These handles fit current Lindsay foot controlled engraved
ArtGraver handpieces, as well as earlier unengraved AirGraver
handpieces. From approx 2003 to present. Classic, Artisan,
BenchJewel and Nitro.
Both type of handles are for Lindsay handpieces, so when ordering
please write a short note in the space provided for notes when
checking out which handpiece you plan to fit and use it with.
SoftIdle™ Stainless Handle
Enjoy less vibration and recoil with your handpiece as well as
improved idle. Metal handles we had available for approx 18
years for the tools. Since the newest development of the
BankNote switch handle that does even more to improve the tool as
described below we went ahead made a run of more of of these less
expensive SoftIdle handles. The SoftIdle handle fits
current engraved ArtGraver handpieces as well as earlier
unengraved AirGraver handpieces, providing improved idle and
increased impact power.
SoftIdle™ Stainless Handle $64
See below information about installing the handle
ArtGraver™ BankNote™ Switch
The novel, patent pending Banknote™ Mode can be turned on/off.
It enhances low end control of impacts of the handpiece that make
shading and bulino line work more controllable. In OFF
position it is similar to the SoftIdle handle sold above. With the
switch in the ON position it improves idle even more as well as
alter the impact characteristics, that are more forgiving
particularly at the low end. Of course it can be shut off
for heavier work.
Banknote™ Mode ArtGraver™
Handle (BankNote™ Switch) - Handle
only (Preorder) $279
See below information about installing the handle.
Installing and removing
SoftIdle™ handle, and BankNote™ handle
On current ArtGraver™ handpiece there is a dimple on
the body for the SoftIdle™ and BankNote™ handle screw to align to
and secure the handle on. The screw does not need to be super
tight, but snug. Align the handle so that the screw will go
into the dimple when tightened.
If your hand piece does not have a dimple, align the flat of the
handle so it is parallel with the hose barb and tighten up the screw
there. If desired, you may return your handpiece so a dimple can be
placed on it. The dimple does help secure the handle as well as
align it. There is no charge for adding the dimple, except for FedEx
return shipping. If you are placing a new order for a
handle and would like the dimple added to your handpiece, simply
write us a note during checkout in the space provided for notes that
you will be sending your handpiece in for the dimple. We can
then wait for your handpiece, add the dimple and install the handle
for you and return your handpiece.
Replacement rubber handle for foot controlled Lindsay handpieces $25
Over time (usually years), depending on the perspiration make up of
one person's hands to the next, a rubber handle may not fit as
tightly. If this is noticed, the rubber handle can be replaced
easily for $25. Or it can be replaced with either of the metal
Metal Handles Now Ship Standard on Foot
All of the below listed engraving sets
A handpiece case, extra screws, o-rings, wrenches, handpiece
tubing, connectors, compressor braided hose for connecting to an air
compressor and owner's manual.
The sharpener sets with basic templates include:
fixture, four diamond bench stones (260, 600, 1200, 2000), plus 4
templates: Universal, Detailing, 105, and Flat & Knife Combo template.
Click to enlarge
Classic ArtistGraver with SoftIdle™ handle, standard nose, foot control regulator setup,
includes stainless and tungsten pistons, one presharpened Carbalt, and 3
HSS graver blanks.
With BankNote™ Mode Handle $1748
Includes Set #1 plus - sharpener set, five Carbalt graver blanks, and
five M42 graver blanks
With BankNote™ Mode Handle $2167
Quick Change extension for standard-nose Classic ArtistGraver and standard-nose
PalmControl Classic ArtisticGraver handpieces.
Available with Single and Quad Indexing.
Single indexing assures quick change to same orientation each time.
Quad indexing allows four choices of orientation of the collet and
therefore the graver you are using.
They are made from 440C stainless and hardened to 60 Rockwell. 60
Rockwell is as hard as a high speed steel graver and therefore these
QC extensions are made for a life time of service. They are detented
for a snap in fit utilizing the internal O-ring in the nose of the
AirGraver handpieces. They extend a graver 5/8".
Classic PalmControl ArtisticGraver with SoftIdle™ handle, standard nose, with air
regulator for use with an air compressor, includes stainless piston, one presharpened Carbalt and 3 HSS graver blanks.
Santophrene handle $2869
Burl wood handle $3069
Order the tungsten piston separately if needed - $125
Includes set #5 plus - sharpener set, CO2 125PSI Regulator with
integrated 20oz CO2 paintball threads, five Carbalt graver blanks, and
five M42 graver blanks
$3371 Santophrene handle
$3571 Burl handle
Order the tungsten piston separately if needed -
Classic bodies - foot controlled or PalmControlled come with Steve
Lindsay engraving. Burl handled PalmControl Classics also include the
scroll and logo engraving impression on the end as pictured. Click to
BenchJewel ArtGraver has a collet nose, SoftIdle™ handle, foot control air regulator
setup, tungsten piston, one presharpened Carbalt and 2 HSS graver
blanks, one short collet, one long collet, adapter, and owners manual.
The handpiece ships with a tungsten installed. Order a stainless piston
separately if needed so you have both $125
Order the BenchJewel collets below if more collets are needed
Order sharpener set separately
Sharpening fixture, four diamond bench stones (260, 600, 1200, 2000),
plus 4 templates: Universal, Detailing, 105, and Flat & Knife Combo
BenchJewel collets and adapters
Two long collets $27
Two short collets $26
Adapter for Long Collets $17.50
One adapter and one long collet $31
An adapter can be moved from one long collet to another long collet.
Two Pack Hex Wrenches $2.50
This disc pedal can be attached to the auxiliary port of
the AirGraver regulator.